Atacama Audio Audition kaiutinjalka

Atacama Audio kaiutinjalka - uutuus-sarja Audition - isolla, leveällä ylälevyllä. Useita korkeuksia 30cm-70cm ja kahta eri väriä. Huomaa, että tuote voidaan asentaa myös kapeampi reuna eteenpäin, jolloin jalka sopii ns.syvälle kaiuttimelle. Hinta on parin hinta. Tehdastilaustuote, varaudu toimitusaikaan. 

Atacama Audio
Atacama Audio Audition kaiutinjalka
  • Atacama Audio Audition kaiutinjalka
  • Atacama Audio Audition
  • Atacama Audio Audition
  • Atacama Audio Audition kaiutinjalka
  • Atacama Audio Audition kaiutinjalka
  • Atacama Audio Audition kaiutinjalka
  • Atacama Audio Audition
  • Atacama Audio Audition kaiutinjalka
439,00 €
Yli 90 euron verkkokauppatilaukset toimituskuluitta kaikkialle Suomeen!
Huom! Ei koske ovelle-toimitusta.


The Audition Series Speaker stands have a large 360mm by 225mm laser cut top plate and can be used with either dimension being front facing. This allows both large, wide but shallow speakers to be supported as well as the more numerous deep cabinet types.

The Audition Series are supplied in a Satin Black paint finish or Diamond White as a cost option.

Each pair of Audition stands are equipped with new 5mm thick laser cut carbon steel base plates, eight heavy duty BZP 8mm adjustable floor spikes featuring stainless steel detailed top caps and upgraded High Load Trapezoidal (HLT) Isolation Gel Pads for the top plates.

We recommend that each pair are mass loaded with Atabites in order to maximize their sonic potential (see below for quantity guidance and recommendations on the amount of mass filler to use).

Floor spikes and HLT Isolation Gel pads are included with each pair of stands, with the option of adding Atabite mass loading filler, top spikes and spike shoes if required.

As these speaker stands use isolation spikes, two sets of four Atacama HD-L (Nickel finish) spike shoes are recommended to protect delicate floor coverings.

Single stands can be supplied if required; please contact your local Atacama stockist or the Atacama sales department on 01455 283251 for pricing and availability (UK only).

Audition speaker stands are designed and manufactured in the UK.

These are a specialist speaker stand, so are made to order. Allow 2-3 week manufacturing times.


Kokonaiskorkeus, sisältäen piikit sekä päälle asenettavat geelipadit: 

Audition 200  235mm   
Audition 300  335mm   
Audition 400  435mm   
Audition 500  535mm   
Audition 600  635mm   
Audition 700  735mm   

Top Plate Dimensions / Ylälevyn mitat

Setup 1. Width 360mm , Depth 225mm  
Setup 2. Width 225mm , Depth 360mm 

Base Plate Dimensions / alalevyn mitat

Setup 1. Width 400mm , Depth 305mm 
Setup 2. Width 305mm , Depth 400mm 

Weight Capacity 20KG per stand.

Note- Supported speaker width/depth dimensions should not exceed speaker stand base plate dimensions.


Atabite quantity recommendation

Below are stated the recommended number of tubes to share between each pair of speaker stands. All vertical poles should be equally filled. Amounts are approximate and will not necessarily completely fill the tubes. It is suggested that you experiment with the exact amount to achieve the best sonic results for your particular system setup as the speakers, room acoustics, cable loom, positioning of the speakers and hifi components will determine how much Atabite filler to use to get the best sound from your speakers.

As a general rule, approximately half to two thirds full gives the best results. If you find the speakers are lacking high end detail and sounding dull at the lower end that usually means you have overfilled the stands and will need to reduce the volume of Atabites in each stand.

 If the speakers are new, it is suggested that the exact amount of Atabites needed will best be determined once they are run in. Refer to your speaker instructions or contact the supplying retailer/ manufacturer for guidelines on running in recommendations. 

Audition 300 2 Tubes        
Audition 400 3 Tubes
Audition 500 4 Tubes
Audition 600 5 Tubes
Audition 700 6 Tubes