Lyngdorf CD-2 cd-soitin

Todella matala ja siisti cd-soitin Lyngdorfilta! 

{Keywords}
Lyngdorf
Lyngdorf CD-2 cd-soitin
  • Lyngdorf CD-2 cd-soitin
  • Lyngdorf CD-2 cd-soitin takaa
  • Lyngdorf CD-2 cd-soitin takaa
  • Lyngdorf CD-2 cd-soitin
  • Lyngdorf CD-2 cd-soitin
2 999,00 €
Yli 90 euron verkkokauppatilaukset toimituskuluitta kaikkialle Suomeen!
Huom! Ei koske ovelle-toimitusta.

Tuotetiedot

PACKED WITH TECHNOLOGY

Designed, developed, and manufactured in Denmark, the pure audio CD-2 provides the unsurpassed performance expected from a Lyngdorf Audio product. Developed with the experience gained from multiple-award-winning Lyngdorf Audio digital amplifiers and CD players, this player is one of the best sounding pure audio CD players on the market.

PURE AUDIO CD

The CD-2 is designed for audio only, and for this reason, using a pure audio drive is both simpler and better. All multi-format drives are based on video designs and clocks, and the audio output is then re-sampled (uncontrolled) to audio output clocks. Many choose to optimize the clock on the drive itself, but no matter what you do, ground potentials are difficult to control and the engine control board is noise-inducing.

The Lyngdorf Audio philosophy is to get the audio signal as clean as possible and to do the optimization based on the Lyngdorf Audio precision clock system. Based on previous work with CD players and fully digital amplifiers, we know the do’s and don’ts of clock systems. The key is low phase noise in the audio band. 

ICC (INTER-SAMPLE CLIPPING CORRECTION)

When music is being mastered, the level is often very high; upon analysis you will often find several consecutive maximum samples, indicating something has been clipped away from the original signal. Audio that exceeds 0 dBFS (decibels relative to full scale) will sound very compressed because the headroom is nonexistent. Sadly, this harsh sound is often related to digitally stored music, as compared to the sound of vinyl. In the CD-2 we reduce the gain with 3 dB; thus, you will enjoy the full dynamic range and a more distortion-free sound

ELECTRICAL DESIGN

The Lyngdorf Audio designed switch mode power supply is extremely well regulated and is filtered and decoupled to provide a low noise and low impedance supply to the digital and analog circuitry. With different supplies from four independent secondary windings on the transformer, the analog and digital supplies are kept separate to minimize digital noise in the analog circuit.

Grounding is optimal, and the entire chassis is connected electrically. The back panel is electrically conductive.

Lyngdorf Audio spends great time and effort in designing products that will not radiate noise. Making a noise and radiation free design has the advantage that it will also make the CD-2 itself immune to noise from the outside and from products that have not had the same attention to details in the design phase.

D/A CONVERTER

The D/A converter section is used to drive a high-quality, single ended, and balanced output stage. The D/A converter is built around the Wolfson WM8740 chip. This, in combination with our balanced design and very fine audiophile op-amps, results in outstanding sonic qualities.

 

SAMPLE RATE CONVERTER

Resampling the output of the CD drive to a low-noise clock suppresses the level of jitter artifacts in the output signal to an absolute minimum. Our state-of-the-art sample rate converters, using special low-noise design techniques, enable the CD-2 to upsample the digital output of the audio drive to a selectable output rate. A major advantage of this is that you can adjust the output for the optimum operating point of a D/A converter. The digital output can deliver 24-bit resolution at a sample rate up to 192 kHz. The analog output section is upsampled in a parallel process to 96 kHz.

Mitat 

Leveys 450 mm 
Syvyys 373 mm 
Kokeus 57 mm 
Nettopaino 6.1 Kg